View MP2488_7302584.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MP2488 200khz, 55v input, 2a high power led driver MP2488 rev. 1.0 www.monolithicpower.com 1 6/20/2011 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. the future of analog ic technology description the MP2488 is a fixed frequency step-down switching regulator to deliver a constant current of up to 2a to high power leds. it integrates a high-side, high voltage power mosfet with a current limit of 3.2a. the wide 4.5v to 55v input range accommodates a variety of step-down applications, making it ideal for automotive, industry and general lighting applications. peak current mode control and 200mv reference are applied for fast loop response, easy compensation and accurate led current regulation. the switching frequency is programmable with an external resistor up to 200khz, which can prevent emi (electromagnetic interference) noise problems. the thermal shut down provides reliable, fault tolerant operations. a 12a quiescent current in shutdown mode allows its use in battery- powered applications. the MP2488 is available in small 3x3mm 10-pin qfn and soic8 with exposed pad packages. features ? wide 4.5v to 55v operating input range ? 220m ? internal power mosfet ? up to 200khz programmable switching frequency ? 130 a quiescent current ? ceramic capacitor stable ? internal soft-start ? up to 97.5% efficiency ? 200mv reference voltage for high efficiency ? available in 3x3mm 10-pin qfn and soic8 with exposed pad packages applications ? high power led driver ? automotive, and general lighting ? constant source for mps green status, please visit mps website under quality assurance. ?mps? and ?the future of analog ic technology? are registered trademarks o f monolithic power systems, inc. typical application MP2488 comp fb freq en vin gnd sw bst v in 8v to 55v control c in c com1 c com2 d1 led- led+ c bst c out l1 r fb r freq c freq r com efficiency vs. input voltage 10 wled@330ma 90 92 94 96 98 100 30 35 40 45 50 55 60 input voltage(v) efficiency(%)
MP2488 ? 2a, 200khz, 55v high-power leds driver MP2488 rev. 1.0 www.monolithicpower.com 2 6/20/2011 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. ordering information part number package top marking free air temperature (t a ) MP2488dq * qfn10(3x3mm) 7g ?40 ? c to +85 ? c MP2488dn ** soic8e MP2488dn ?40 ? c to +85 ? c *for tape & reel, add suffix ?z (eg. MP2488dq?z); for rohs compliant packaging, add suffix ?lf (eg. MP2488dq?lf?z) ** for tape & reel, add suffix ?z (eg. MP2488 dn?z); for rohs compliant packaging, add suffix ?lf (eg. MP2488 dn?lf?z) package reference top view sw sw en comp fb 1 2 3 4 5 bst vin vin freq gnd 10 9 8 7 6 exposed pad qfn10(3x3mm) sw en comp fb bst vin freq gnd 1 2 3 4 8 7 6 5 top view exposed pad soic8e absolute maxi mum ratings (1) supply voltage (v in ) ..................... ?0.3v to +60v switch voltage (v sw ) ............ ?0.5v to v in + 0.5v bst to sw ..................................... ?0.3v to +5v all other pins ................................. ?0.3v to +5v junction temperature ............................... 150 ? c lead temperature .................................... 260 ? c storage temperature .............. ?65c to +150 ? c continuous power dissipation (t a =+25 ? c ) (2) qfn10(3x3mm) ......................................... 2.5w soic8 (exposed pad) ............................... 2.5w recommended operating conditions (3) supply voltage v in ........................... 4.5v to 55v maximum junction temp. (t j ) ............... +125 ? c thermal resistance (4) ja jc qfn10(3x3mm) ...................... 50 ...... 12 ... ? c/w soic8 (exposed pad) ............ 50 ...... 10 ... ? c/w notes: 1) exceeding these ratings may damage the device. 2) the maximum allowable power dissipation is a function of the maximum junction temperature t j (max), the junction-to- ambient thermal resistance ja , and the ambient temperature t a . the maximum allowable continuous power dissipation at any ambient temperature is calculated by p d (max)=(t j (max)- t a )/ ja . exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. internal thermal shutdown circuitry protects the device from permanent damage. 3) the device is not guaranteed to function outside of its operating conditions. 4) measured on jesd51-7 4-layer board.
MP2488 ? 2a, 200khz, 55v high-power leds driver MP2488 rev. 1.0 www.monolithicpower.com 3 6/20/2011 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. electrical characteristics v in = 12v, v en = 2.5v, v comp = 1.4v, t a = +25 ? c, unless otherwise noted. specifications over temperature are guaranteed by design and characterization. parameter symbol condition min typ max units feedback voltage v fb 4.5v < v in < 55v 188 200 212 mv upper switch on resistance ( 5 ) r ds ( on ) v bst ? v sw = 5v 220 m ? upper switch leakage v en = 0v, v sw = 0v 0.1 a current limit 2.6 3.2 a error amp voltage gain a vea 400 v/v error amp transconductance g ea i comp = 3a 350 a/v error amp min source current v fb = 175mv 10 a error amp min sink current v fb = 225mv -10 a vin uvlo threshold v in rising 2.7 3.0 3.3 v vin uvlo hysteresis 0.4 v soft-start time ( 5 ) 20mv < v fb < 190mv 0.18 ms oscillator frequency f s r freq = 495k ? 150 200 250 khz minimum switch on time ( 5 ) 100 ns shutdown supply current v en < 0.3v 12 25 a quiescent supply current no load, v fb = 240mv 130 a thermal shutdown hysteresis = 20 ? c 150 ? c minimum off time ( 5 ) 100 ns minimum on time ( 5 ) 100 ns en up threshold 1.3 1.5 1.7 v en threshold hysteresis 300 mv note: 5) guaranteed by design.
MP2488 ? 2a, 200khz, 55v high-power leds driver MP2488 rev. 1.0 www.monolithicpower.com 4 6/20/2011 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. pin functions qfn pin # soic8 pin # name description 1, 2 1 sw switch node. this is the output from the high-side switch. a low v f schottky rectifier to ground is required. the rectifier must be close to the sw pins to reduce switching spikes. 3 2 en enable input. pulling this pin below the specified threshold shuts the chip down. pulling it up above the specified threshold or leaving it floating enables the chip. 4 3 comp compensation. this node is the output of the gm error amplifier. control loop frequency compensation is applied to this pin. 5 4 fb feedback. this is the input to the error amp lifier. an external current sensing resistor is connected in series with the leds to gnd. the feedback voltage is connected to this pin and is compared to the internal +200mv reference to set the regulation current. 6 5 gnd, exposed pad ground. it should be connected as close as possible to the output capacitor avoiding the high current switch paths. connect ex posed pad to gnd plane for optimal thermal performance. 7 6 freq switching frequency program input. connect a resistor from this pin to ground to set the switching frequency. 8, 9 7 vin input supply. this supplies power to all the internal control circuitry, both bs regulators and the high-side switch. a deco upling capacitor to ground must be placed close to this pin to minimize the switching spikes. 10 8 bst bootstrap. this is the pos itive power supply for the internal floating high-side mosfet driver. connect a bypass capacitor between this pin and sw pin.
MP2488 ? 2a, 200khz, 55v high-power leds driver MP2488 rev. 1.0 www.monolithicpower.com 5 6/20/2011 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. typical performanc e characteristics v in =44v, i led =330ma, 10 wled series, unless otherwise noted. v in 20v/div v sw 20v/div v sw 20v/div v sw 50v/div i led 200ma/div i led 200ma/div i led 200ma/div i inductor 200ma/div i inductor 200ma/div v en 5v/div v comp 500mv/div steady state operation 2ms/div 4us/div pwm dimming f pwm =200hz,d pwm =50% en shutdown v en 5v/div v sw 50v/div i led 200ma/div i inductor 200ma/div v en 5v/div en start up efficiency vs. input voltage 10 wled@330ma 90 92 94 96 98 100 30 35 40 45 50 55 60 input voltage(v) efficiency(%)
MP2488 ? 2a, 200khz, 55v high-power leds driver MP2488 rev. 1.0 www.monolithicpower.com 6 6/20/2011 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. block diagram -- + logic -- + 0.18ms ss ss comp isw vin bst sw freq gnd comp fb en ss 0v2 reference uvlo internal regulators oscillator figure 1?functional block diagram
MP2488 ? 2a, 200khz, 55v high-power leds driver MP2488 rev. 1.0 www.monolithicpower.com 7 6/20/2011 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. operation pwm control mode MP2488 operates in a fixed frequency, peak current control mode to regulate the led current. a pwm cycle is initiated by the internal clock. the power mosfet is turned on and remains on until its current reaches the value set by the comp voltage. when the power switch is off, it remains off for at least 100ns before the next cycle starts. in one pwm period, the current in the power mosfet does not reach the comp set current value, the power mosfet remains on, saving a turn-off operation. error amplifier the error amplifier compares the fb pin voltage with the internal reference (ref) and outputs a current proportional to the difference between the two. this output current is then used to charge the external compensation network to form the comp voltage, which is used to control the power mosfet current. during operation, the minimum comp voltage is clamped to 0.9v and its maximum is clamped to 2.0v. comp is internally pulled down to gnd in shutdown mode. comp should not be pulled up beyond 2.6v. internal regulator most of the internal circuitries are powered from the 2.6v internal regulator. this regulator takes the vin input and operates in the full vin range. when vin is greater than 3.0v, the output of the regulator is in full regulation. when vin is lower than 3.0v, the output decreases. enable control the MP2488 has a dedicated enable control pin (en). with high enough input voltage, the chip can be enabled and disabled by en which has positive logic. its falling threshold is a precision 1.2v, and its rising threshold is 1.5v (300mv higher). when floating, en is pulled up to about 3.0v by an internal 1a current source so it is enabled. to pull it down, 1a current capability is needed. when en is pulled down below 1.2v, the chip is put into the lowest shutdown current mode. when en is higher than zero but lower than its rising threshold, the chip is still in shutdown mode but the shutdown current increases slightly. under-voltage lockout (uvlo) under-voltage lockout (uvlo) is implemented to protect the chip from operating at insufficient supply voltage. the uvlo rising threshold is about 3.0v while its falling threshold is a consistent 2.6v. internal soft-start the soft-start is implemented to prevent the led current from overshooting during startup and short circuit recovery. when the chip starts, the internal circuitry generates a soft-start voltage (ss) ramping up from 0v to 2.6v. when it is lower than the internal reference (ref), ss overrides ref so the error amplifier uses ss as the reference. when ss is higher than ref, ref regains control. thermal shutdown thermal shutdown is implemented to prevent the chip from operating at exceedingly high temperatures. when the silicon die temperature is higher than its upper threshold, it shuts down the whole chip. when the temperature is lower than its lower threshold, the chip is enabled again. floating driver and bootstrap charging the floating power mosfet driver is powered by an external bootstrap capacitor. this floating driver has its own uvlo protection. this uvlo?s rising threshold is 2.2v with a threshold of 150mv. the driver?s uvlo is soft-start related. in case the bootstrap voltage hits its uvlo, the soft-start circuit is reset. to prevent noise, there is 20s delay before the reset action. when bootstrap uvlo is gone, the reset is off and then soft-start process resumes. the bootstrap capacitor is charged and regulated to about 4v by the dedicated internal bootstrap regulator. when the voltage between the bst and sw nodes is lower than its regulation, a pmos pass transistor connected from vin to bst is turned on. the charging current path is from vin, bst and then to sw. external circuit should provide enough voltage headroom to facilitate the charging.
MP2488 ? 2a, 200khz, 55v high-power leds driver MP2488 rev. 1.0 www.monolithicpower.com 8 6/20/2011 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. as long as vin is sufficiently higher than sw, the bootstrap capacitor can be charged. when the power mosfet is on, vin is about equal to sw so the bootstrap capacitor cannot be charged. when the external diode is on, the difference between vin and sw is largest, thus making it the best period to charge. when there is no current in the inductor, sw equals the output voltage v out so the difference between v in and v out can be used to charge the bootstrap capacitor. at higher duty cycle operation condition, the time period available to the bootstrap charging is less so the bootstrap capacitor may not be sufficiently charged. in case the internal circuit does not have sufficient voltage and the bootstrap capacitor is not charged, extra external circuitry can be used to ensure the bootstrap voltage is in the normal operational region. refer to external bootstrap diode in application section. current comparator and current limit the power mosfet current is accurately sensed via a current sense mosfet. it is then fed to the high speed current comparator for the current mode control purpose. the current comparator takes this sensed current as one of its inputs. when the power mosfet is turned on, the comparator is first blanked till the end of the turn- on transition to avoid noise issues. the comparator then compares the power switch current with the comp voltage. when the sensed current is higher than the comp voltage, the comparator output is low, turning off the power mosfet. the cycle-by-cycle maximum current of the internal power mosfet is internally limited. startup and shutdown if both vin and en are higher than their appropriate thresholds, the chip starts. the reference block starts first, generating stable reference voltage and currents, and then the internal regulator is enabled. the regulator provides stable supply for the remaining circuitries. while the internal supply rail is up, an internal timer holds the power mosfet off for about 50s to blank the startup glitches. when the internal soft-start block is enabled, it first holds its ss output low to ensure the remaining circuitries are ready and then slowly ramps up. three events can shut down the chip: en low, vin low and thermal shutdown. in the shutdown procedure, power mosfet is turned off first to avoid any fault triggering. the comp voltage and the internal supply rail are then pulled down. programmable oscillator the MP2488 oscillating frequency is set by an external resistor, r freq from the freq pin to ground. the value of r freq can be calculated from: freq s 100000 r(k ? )= -5 f(khz) to get f s =200khz, r freq =495k ? . a ceramic capacitor c freq should be parallel to r freq to decouple the noise, 1nf is enough for most applications.
MP2488 ? 2a, 200khz, 55v high-power leds driver MP2488 rev. 1.0 www.monolithicpower.com 9 6/20/2011 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. application information component selection setting the led current the led current is set using a sensing resistor, which is in series with the leds and connected to gnd. the voltage on the sensing resistor is connected to fb pin. fb led fb v i r ? for example, for a 700ma led current, r fb is 287m ? . inductor l1 the inductor is required to supply constant current to the output load while being driven by the switched input voltage. a larger value inductor will help to reduce the output filter capacitance for the same led current ripple. however, the larger value inductor will have a larger physical size, higher series resistance, and/or lower saturation current. a good rule for determining the inductance to use is to allow the peak-to-peak ripple current in the inductor to be approximately 30% to 40% of the led current. also, make sure that the peak inductor current is below the maximum switch current limit. the inductance value can be calculated by: out out sl in vv l1= (1- ) f iv ? ? , out f vnv ?? where v out is the output voltage to drive the leds, v in is the input voltage, f s is the switching frequency, v f is one led diode forward voltage drop, n is the numbers of leds in series, and ? i l is the peak-to-peak inductor ripple current. choose an inductor that will not saturate under the maximum inductor peak current. the peak inductor current can be calculated by: out out lp led sin vv ii (1 ) 2f l1 v ?? ?? ?? where i led is the led current. output rectifier diode the output rectifier diode supplies the current to the inductor when the high-side switch is off. to reduce losses due to the diode forward voltage and recovery times, use a schottky diode. choose a diode whose maximum reverse voltage rating is greater than the maximum input voltage, and whose current rating is greater than the maximum load current. table 2 lists example schottky diodes and manufacturers. table 1?diode selection guide diodes voltage/ current rating manufacturer b280-13-f 80v, 2a diodes inc. b380-13-f 80v, 3a diodes inc. cmsh2-100m 100v, 2a central semi cmsh3-100ma 100v, 3a central semi input capacitor c in the input current to the step-down converter is discontinuous, therefore a capacitor is required to supply the ac current to the step-down converter while maintaining the dc input voltage. use low esr capacitors for the best performance. ceramic capacitors are preferred, but tantalum or low-esr electrolytic capacitors may also suffice. for simplification, choose the input capacitor with rms current rating greater than half of the maximum load current. the input capacitor (c1) can be electrolytic, tantalum or ceramic. when using electrolytic or tantalum capacitors, a small, high quality ceramic capacitor, i.e. 0.1 f, should be placed as close to the ic as possible. when using ceramic capacitors, make sure that they have enough capacitance to provide sufficient charge to prevent excessive voltage ripple at input. the input voltage ripple caused by capacitance can be estimated by: out out led in sin in in vv i v1 fc v v ?? ?? ? ?? ?? ? ??
MP2488 ? 2a, 200khz, 55v high-power leds driver MP2488 rev. 1.0 www.monolithicpower.com 10 6/20/2011 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. output capacitor c out the output capacitor (c out ) is required to reduce the led current ripple. ceramic, tantalum, or low esr electrolytic capacitors are recommended. low esr capacitors are preferred to keep the output voltage ripple low so that the ac ripple current through the leds is small. the output voltage ripple can be estimated by: out out out 2 in sout vv v1 v 8f l1c ?? ??? ?? ??? ?? for most application, a 2.2uf~4.7uf ceramic capacitor is recommended. compensation components MP2488 employs current mode control for easy compensation and fast transient response. the system stability and transient response are controlled through the comp pin. comp pin is the output of the internal error amplifier. a series capacitor-resistor combination (r com and c com1 ) sets a pole-zero combination to control the characteristics of the control system. the dc gain of the current feedback loop is given by: vdc fb cs vea arga ??? where a vea is the error amplifier voltage gain, 400v/v; g cs is the current sense transconductance, 8a/v; r fb is the current sensing resistor value. the system has two poles of importance. one is due to the compensation capacitor (c com1 ) and the output resistor of error amplifier (r ea =a vea /g ea ). g ea is the error amplifier transconductance, 500 a/v. the other is due to the output capacitor and the leds? ac resistor (r led = ? v out / ? i led ). these poles are located at: p1 com1 ea 1 f 2c r ? ?? ? p2 out led 1 f 2c r ? ?? ? the system has one zero of importance, due to the compensation capacitor (c com1 ) and the compensation resistor (r com ). this zero is located at: z1 com1 com 1 f 2c r ? ?? ? the system may have another zero of importance, if the output capacitor has a large capacitance and/or a high esr value. the zero, due to the esr and capacitance of the output capacitor, is located at: esr out esr 1 f 2c r ? ?? ? in this case, a third pole set by the compensation capacitor (c com2 ) and the compensation resistor (r com ) is used to compensate the effect of the esr zero on the loop gain. this pole is located at: p3 com2 com 1 f 2c r ? ?? ? the goal of compensation design is to shape the converter transfer function to get a desired loop gain and phase margin. the system crossover frequency where the feedback loop has the unity gain is important. lower crossover frequencies result in slower line and load transient responses, while higher crossover frequencies could cause system unstable. a good rule of thumb is to set the crossover frequency to approximately one- tenth of the switching frequency. to optimize the compensation components for conditions, the following procedure can be used. 1. choose the compensation resistor (r com ) to set the desired crossover frequency. determine the r com value by the following equation: out led c com fb ea cs 2c r f r rgg ? ??? ? ?? where f c is the desired crossover frequency. 2. choose the compensation capacitor (c com1 ) to achieve the desired phase margin. for applications with typical inductor values, setting the compensation zero, f z1 , below one forth of the crossover frequency provides sufficient phase margin. determine the c com1 value by the following equation: com1 com c 4 c 2r f ? ?? ?
MP2488 ? 2a, 200khz, 55v high-power leds driver MP2488 rev. 1.0 www.monolithicpower.com 11 6/20/2011 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. 3. determine if the second compensation capacitor (c com2 ) is required, which is connected from comp pin to gnd. it is required if the esr zero of the output capacitor is located at less than half of the switching frequency: s out esr f 1 2c r 2 ? ?? ? if this is the case, then add the second compensation capacitor (c com2 ) to set the pole f p3 at the location of the esr zero. determine the c com2 value by the equation: out esr com2 com cr c r ? ? external bootstrap diode an external bootstrap diode may enhance the efficiency of the regulator. in below cases, an external bst diode is recommended from the 5v to bst pin: ? there is a 5v rail available in the system; ? vin is not greater than 5v; ? vout is between 3.3v and 5v; the bootstrap diode can be a low cost one such as in4148 or bat54. MP2488 sw bst 5v figure 2?external bootstrap diode
MP2488 ? 2a, 200khz, 55v high-power leds driver MP2488 rev. 1.0 www.monolithicpower.com 12 6/20/2011 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. typical application circuits MP2488 comp fb freq en vin gnd sw bst v in 8v to 55v control c in c com1 c com2 47pf d1 b180-7-f led- led+ c bst c out r fb i led r freq c freq r com =700ma 22nf 100nf 1nf figure 3?700ma wled driver application
MP2488 ? 2a, 200khz, 55v high-power leds driver MP2488 rev. 1.0 www.monolithicpower.com 13 6/20/2011 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. package information qfn10 (exposed pad) (3x3mm) side view top view 1 10 6 5 bottom view 2.90 3.10 1.45 1.75 2.90 3.10 2.25 2.55 0.50 bsc 0.18 0.30 0.80 1.00 0.00 0.05 0.20 ref pin 1 id marking 1.70 0.50 0.25 recommended land pattern 2.90 note: 1) all dimensions are in millimeters. 2) exposed paddle size does not include mold flash. 3) lead coplanarity shall be 0.10 millimeter max. 4) drawing conforms to jedec mo-229, variation veed-5. 5) drawing is not to scale. pin 1 id see detail a 2.50 0.70 pin 1 id option b r0.20 typ. pin 1 id option a r0.20 typ. detail a 0.30 0.50 pin 1 id index area
MP2488 ? 2a, 200khz, 55v high-power leds driver notice: the information in this document is subject to change wi thout notice. users should warra nt and guarantee that third party intellectual property rights are not infringed upon w hen integrating mps products into any application. mps will not assume any legal responsibility for any said applications. MP2488 rev. 1.0 www.monolithicpower.com 14 6/20/2011 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2011 mps. all rights reserved. soic8 (exposed pad) see detail "a" 0.0075(0.19) 0.0098(0.25) 0.050(1.27) bsc 0.013(0.33) 0.020(0.51) seating plane 0.000(0.00) 0.006(0.15) 0.051(1.30) 0.067(1.70) top view front view side view bottom view note: 1) control dimension is in inches. dimension in bracket is in millimeters. 2) package length does not include mold flash, protrusions or gate burrs. 3) package width does not include inte rlead flash or protrusions. 4) lead coplanarity (bottom of leads after forming) shall be 0.004" inches max. 5) drawing conforms to jedec ms-012, variation ba. 6) drawing is not to scale. 0.089(2.26) 0.101(2.56) 0.124(3.15) 0.136(3.45) recommended land pattern 0.213(5.40) 0.063(1.60) 0.050(1.27) 0.024(0.61) 0.103(2.62) 0.138(3.51) 0.150(3.80) 0.157(4.00) pin 1 id 0.189(4.80) 0.197(5.00) 0.228(5.80) 0.244(6.20) 14 85 0.016(0.41) 0.050(1.27) 0 o -8 o detail "a" 0.010(0.25) 0.020(0.50) x 45 o 0.010(0.25) bsc gauge plane

▲Up To Search▲

Price & Availability of MP2488

	To Download MP2488 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .